Guide
Measure Grinder Clearance Under Kitchen Cabinets
Measure from the counter to the lowest obstruction, then subtract the grinder's closed height. Check whether the remaining space lets you open or remove the lid, add beans, and reach each control without sliding the grinder.
Who this helps: For home coffee setups where a grinder will sit under an upper cabinet or shelf. Follow the manufacturer's operating instructions and check your exact model before using it in a tight space.
Measure the counter to its lowest overhead obstruction
Use a rigid tape measure to find the smallest vertical gap above the planned spot. Start at the surface where the feet will rest, and check near the wall, at the front of the cabinet, and above the lid position. A cabinet lip, lighting strip, shelf rail, or hanging accessory can sit lower than the cabinet bottom. If you use a mat or tray under the grinder, measure from its top instead of the bare counter.
Write down the smallest reading in inches or millimeters. Move the tape along the front-to-back path the grinder will take. A space may have plenty of clearance near the wall yet be too short where the cabinet front crosses the hopper.
Check closed height and loading clearance separately
Find the manufacturer's closed height for the exact grinder and hopper combination. Then determine what moves in use. A lift-off lid needs space for the lid and your fingers. A hinged hopper cover needs room for the arc it follows. A grinder with a removable hopper can also require an upward lift before it clears the collar.
Check the manual or look for a side-view drawing that shows the open configuration. If only the closed dimensions are published, the open height remains unknown. Measure a display unit where available, or leave room to pull the grinder forward before filling it. The daily workflow matters more than how neatly the grinder slides into place when shut.
Work through a clearance calculation
Imagine a counter with 330 mm of clearance at the cabinet trim. Fellow lists its Opus 2 at 267 mm high in its product specifications. This leaves 63 mm above the closed body in the example. If your own simulated loading movement needs 85 mm, there is a 22 mm shortfall for that motion. The grinder could sit there closed, but loading beans under the trim would require a lower working position or a forward slide.
The 85 mm is an example allowance, not a Fellow specification. Measure your lid with the grinder unpowered if you have the unit, or sketch the lid path and the position of your hand before buying. Record the unloaded and in-use heights separately.
Include the cord, catch cup, and adjustment dial
Measure from the backsplash to the counter edge and check where the machine's cord leaves the housing. Leave enough depth to route the cord without pinching it behind the grinder. Hold a mug or dosing cup at the planned front edge and imitate the motion of removing the catch cup. A wall, espresso machine, or side panel can also block the grind adjustment dial even when height is adequate.
Fellow's Opus 2 is listed at 206 mm long by 130 mm wide, with a side adjustment dial. Model dimensions give a starting footprint. The workspace should also include the hand position for the dial and the path the cup travels as it comes out.
Make a cardboard footprint and rehearse the whole routine
Cut a rectangle the same size as the grinder's stated footprint. Put a box or stack of books of the same height on it, then rehearse filling the hopper, reaching the control, and retrieving the catch cup. Open nearby cabinet doors and drawers during the rehearsal, and keep the worktop in the same layout you use most mornings.
If a parked grinder needs to move before grinding, check how far forward it must travel and whether it stays supported by the counter. Set a removable marker on the counter edge to identify the forward position. Choose a stationary spot or a smaller grinder if pulling it forward would put the feet too close to the edge.
Save a fit checklist for comparing other models
Keep a note with the counter clearance, grinder height, remaining space, lid opening requirement, plug position, and catch-cup removal direction. Check daily loading separately from occasional cleaning. A grinder you can move for burr maintenance might still be convenient if you can fill it and remove the grounds in place.
When comparing two models, ask which needs fewer movements in the space you have. One may be shorter but have a hinged lid that rises higher than the removable cover on the other. Use the measured requirements to compare them under the same cabinet.
FAQ
How much space should I leave above a coffee grinder?
There is no universal overhead allowance. Start with the difference between the lowest cabinet obstruction and closed grinder height. Confirm that the remaining space covers the lid movement and the way you hold the bean container. Use the manufacturer's clearances if the manual gives them.
Can I trust the grinder height in a store listing?
Use the product documentation for the exact model and hopper configuration, then check whether the figure is the overall closed height. Different hoppers or accessories can change both the closed height and the room needed above it. A listing figure alone cannot confirm operating clearance.
What should I check on a single-dose grinder?
Check the height needed to lift the lid and tip your dosing cup into the opening. The top of the container and your knuckles can rise above the lid, so rehearse that motion. Also make sure the catch cup can come out at the front while the grinder remains in place.
Sources
- Fellow: Opus 2 specifications and controls — checked 2026-11-20